Re: [hatari-devel] DSP for Previous

[Andreas Grabher <andreas.grabher@xxxxxxxxxxxx>]

Sorry, of course that is not a problem in the DSP code. It was my problem not understanding how it is intended to work on the first try.

But i have another question regarding interrupts. The host command interrupt has vector 0x24. But in the emulator vector 0xFF is assigned to it. Of course that is replaced with the vector provided by the host. But is there a special reason not using 0x24? Or did i miss something in the datasheet?

Am 07.06.2015 um 23:48 schrieb Laurent Sallafranque <laurent.sallafranque@xxxxxxx>:

Hi,

> Found the problem. Obviously the values for the interrupts are not the vectors, but indexes to a table.

That's not really a problem. I just needed some constants to give a name to my interrupts into the code.

Regards

Laurent

Le 06/06/2015 13:42, Andreas Grabher a écrit :

Found the problem. Obviously the values for the interrupts are not the vectors, but indexes to a table.

Am 06.06.2015 um 10:39 schrieb Andreas Grabher <andreas.grabher@xxxxxxxxxxxx>:

I have another question about the DSP code. The CPU needs to interrupt the DSP using IRQB.

I looked at the available interrupt vectors in dsp_core.h:

#define DSP_INTER_RESET 0x0
#define DSP_INTER_ILLEGAL 0x1
#define DSP_INTER_STACK_ERROR 0x2
#define DSP_INTER_TRACE 0x3
#define DSP_INTER_SWI 0x4
#define DSP_INTER_HOST_COMMAND 0x5
#define DSP_INTER_HOST_RCV_DATA 0x6
#define DSP_INTER_HOST_TRX_DATA 0x7
#define DSP_INTER_SSI_RCV_DATA_E 0x8
#define DSP_INTER_SSI_RCV_DATA 0x9
#define DSP_INTER_SSI_TRX_DATA_E 0xa
#define DSP_INTER_SSI_TRX_DATA 0xb

If does not match the on from the data sheet (DSP56000/560001UM rev2, see appended file):

0x0000: Hardware RESET

0x0002: Stack error

0x0004: Trace

0x0006: SWI

0x0008: IRQA

0x000A: IRQB

...

What might be the reason for this? Mistake or intentional difference?

<interrupt sources.png>

Am 04.06.2015 um 11:42 schrieb Andreas Grabher <andreas.grabher@xxxxxxxxxxxx>:

Luckily it turned out that the mode bits in the system control register are inverted. So mode 2 is mode 1 and that is the one that is implemented.

With some additions to the code (some bits in ICR seemed to be ignored) now at least it does something.

Maybe some of these changes are useful for Hatari too (see appended file). I'd be glad if someone could check them for correctness.

btw. It seems to me that Hatari is releasing the HREQ interrupt in a wrong way. DSP should release it, not CPU.

<dsp_patch3.diff>

Am 03.06.2015 um 19:10 schrieb Douglas Little <doug694@xxxxxxxxxxxxxx>:

Hi,

I added the DSP code from Hatari v1.8.0. It was easy to make it compile. But then i ran into an early problem:

The 56001 has 4 operating modes:

Has anyone some insight in how the other modes could be implemented? At first look the differences between the modes seem to be mostly related to DSP reset.

IIRC the modes affect two things - the reset 'delay' (16 cycles vs 'lots') and the address of external memory to bootstrap from. However, I haven't used any of that so there may be further complications :)

D