| Re: [crisos] Problemi con la creazione dei device ... |
[ Thread Index |
Date Index
| More lists.tuxfamily.org/crisos Archives
]
- To: crisos@xxxxxxxxxxxxxxxxxxx
- Subject: Re: [crisos] Problemi con la creazione dei device ...
- From: Vittorio Foschi <vittorio.foschi@xxxxxxxxx>
- Date: Thu, 15 May 2008 14:44:58 +0200
- Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:received:received:subject:from:to:in-reply-to:references:content-type:date:message-id:mime-version:x-mailer:content-transfer-encoding; bh=jvZ8KFCVCly3cpQejO6AlJGq+xTBVvQGATzbIbr2mMw=; b=MPP7CscFVrPMremdggiiwmVSl0u8eiibacQOuEd6kZk71XyJJ1kImajoLlD5nNibTS17Ujg+WgxBWGe8Bv7Nl3sctpa3yy8OCyzQoy95v4peNHVdbewfsALo5crPTTnN6MIoRBsc9qOHKoPbJMy2L9IKH7WAv9mdfih3ElIzOj8=
- Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=subject:from:to:in-reply-to:references:content-type:date:message-id:mime-version:x-mailer:content-transfer-encoding; b=vP9KRu40942vNA34kL/O3SiB8pHIblgtJwHWAn4e+x+c5WkSdtq82vcCw5Cwwzg5RbrpqPkSTdtcrUXG1jiuNxJWiFqhlwa+8oLWnHGRLA5GqIBZB/oKhqg4XyugivbWoc8OTsRAXv/Q8OB4OCdSFG7iFCPLLi95RxP0nhoiD1o=
Il giorno mer, 14/05/2008 alle 13.27 +0200, Claudio ha scritto:
> Ciao,
>
> Il 9 maggio 2008 23.04, Vittorio Foschi <vittorio.foschi@xxxxxxxxx> ha scritto:
>
> > Devo selezionare qualcosa di particolare nel menuconfig o nel
> > kernel_menuconfig ?
>
> Verifica in kernel_menuconfig i seguenti settaggi:
> Drivers for built-in interfaces --->
> [*] Serial port 1 enabled
> [*] Serial port 2 enabled
>
> Di default queste opzioni sono disattivate.
>
>
> (en)
> If you need to use ttyS1 and ttyS2 on your board please check the
> following setting on kernel_menuconfig:
> Drivers for built-in interfaces --->
> [*] Serial port 1 enabled
> [*] Serial port 2 enabled
>
> These settings are disable on default CrisOs firmware.
>
>
> Ciao
>
> ---
> CrisOs mailing list
> Official multi-language http://www.crisos.org/ mailing list
>
> For unsubscribe send empty mail to: crisos-request@xxxxxxxxxxxxxxxxxxx with subject unsubscribe.
The options for serial ports are checked correctly ( i enabled Port 2
and 3 ) ... and if i make this commands on my Fox ( after loaded the
firmware ) :
mknod /dev/ttyS0 c 4 64
mknod /dev/ttyS2 c 4 66
mknod /dev/ttyS3 c 4 67
All is ok. My application open ttyS2 and communicate with device attach
on serial port.
---
CrisOs mailing list
Official multi-language http://www.crisos.org/ mailing list
For unsubscribe send empty mail to: crisos-request@xxxxxxxxxxxxxxxxxxx with subject unsubscribe.