| Slitaz 3.0 - Intel ATOM/Poulsbo: hard-disk not seen |
[ Thread Index |
Date Index
| More lists.tuxfamily.org/slitaz Archives
]
Hi list,
I have a PC with CPU Intel Atom Z520 and Poulsbo chipset and I can't see
my hard-disk with Slitaz 3.0. I mean output of "fdisk -l" is empty and
dmesg doesn't report any hard-disk. I have to point out that using
Slitaz 2.0 everything works fine and I can mount the hard-disk and use
it without problems.
I think there are a lot of users here with this problem because this is
the same chipset used in many nettops.
Anybody here knows the solution to this problem, maybe some boot option
or maybe some modules to load?
Thanks a lot
Regards
Luca
Here is the output of lspci:
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH
Poulsbo) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation System Controller
Hub (SCH Poulsbo) Graphics Controller (rev 07)
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH
Poulsbo) HD Audio Controller (rev 07)
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 1 (rev 07)
00:1c.1 PCI bridge: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 2 (rev 07)
00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #1 (rev 07)
00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #2 (rev 07)
00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #3 (rev 07)
00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH
Poulsbo) USB EHCI #1 (rev 07)
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH
Poulsbo) LPC Bridge (rev 07)
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH
Poulsbo) IDE Controller (rev 07)
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network
Connection
02:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI
Express-to-PCI Bridge (rev aa)
03:0f.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet
Pro 100 (rev 10)
here is the output of lspci -n
00:00.0 0600: 8086:8100 (rev 07)
00:02.0 0300: 8086:8108 (rev 07)
00:1b.0 0403: 8086:811b (rev 07)
00:1c.0 0604: 8086:8110 (rev 07)
00:1c.1 0604: 8086:8112 (rev 07)
00:1d.0 0c03: 8086:8114 (rev 07)
00:1d.1 0c03: 8086:8115 (rev 07)
00:1d.2 0c03: 8086:8116 (rev 07)
00:1d.7 0c03: 8086:8117 (rev 07)
00:1f.0 0601: 8086:8119 (rev 07)
00:1f.1 0101: 8086:811a (rev 07)
01:00.0 0200: 8086:10d3
02:00.0 0604: 10b5:8112 (rev aa)
03:0f.0 0200: 8086:1229 (rev 10)
and here the output of dmesg:
>ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 32bit mmio: [0xdff80000-0xdfffffff]
pci 0000:00:02.0: reg 14 io port: [0xe880-0xe887]
pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xd7ffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xdff60000-0xdff7ffff]
pci 0000:00:1b.0: reg 10 64bit mmio: [0xdff5c000-0xdff5ffff]
pci 0000:00:1b.0: PME# supported from D0 D3hot
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xe480-0xe49f]
pci 0000:00:1d.1: reg 20 io port: [0xe080-0xe09f]
pci 0000:00:1d.2: reg 20 io port: [0xef00-0xef1f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xdff5bc00-0xdff5bfff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:01:00.0: reg 10 32bit mmio: [0xcfce0000-0xcfcfffff]
pci 0000:01:00.0: reg 18 io port: [0xc880-0xc89f]
pci 0000:01:00.0: reg 1c 32bit mmio: [0xcfcdc000-0xcfcdffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0xcfcc0000-0xcfcc07ff]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xcfc00000-0xcfcfffff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: PME# supported from D0 D1 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xd000-0xdfff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xcfd00000-0xcfdfffff]
pci 0000:03:0f.0: reg 10 32bit mmio: [0xcfdff000-0xcfdfffff]
pci 0000:03:0f.0: reg 14 io port: [0xd880-0xd8bf]
pci 0000:03:0f.0: reg 18 32bit mmio: [0xcfdc0000-0xcfddffff]
pci 0000:03:0f.0: supports D1 D2
pci 0000:03:0f.0: PME# supported from D0 D1 D2 D3hot
pci 0000:03:0f.0: PME# disabled
pci 0000:02:00.0: bridge io port: [0xd000-0xdfff]
pci 0000:02:00.0: bridge 32bit mmio: [0xcfd00000-0xcfdfffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKE] (IRQs *9 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 9 *15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *9 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 9 *15)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0x20000000-0x7fffffff has been reserved
system 00:01: iomem range 0x1fc00000-0x1fffffff has been reserved
system 00:08: ioport range 0xa60-0xa6f has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x900-0x9f3 has been reserved
system 00:09: ioport range 0x400-0x43f has been reserved
system 00:09: ioport range 0x480-0x4bf has been reserved
system 00:09: iomem range 0xf0000000-0xf0003fff has been reserved
system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0f: iomem range 0x0-0x9ffff could not be reserved
system 00:0f: iomem range 0xc0000-0xcffff could not be reserved
system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
system 00:0f: iomem range 0x100000-0x1fbfffff could not be reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0: IO window: 0xc000-0xcfff
pci 0000:00:1c.0: MEM window: 0xcfc00000-0xcfcfffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
pci 0000:02:00.0: IO window: 0xd000-0xdfff
pci 0000:02:00.0: MEM window: 0xcfd00000-0xcfdfffff
pci 0000:02:00.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.1: IO window: 0xd000-0xdfff
pci 0000:00:1c.1: MEM window: 0xcfd00000-0xcfdfffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:02:00.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:01: resource 1 mem: [0xcfc00000-0xcfcfffff]
pci_bus 0000:02: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:02: resource 1 mem: [0xcfd00000-0xcfdfffff]
pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:03: resource 1 mem: [0xcfd00000-0xcfdfffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Switched to NOHz mode on CPU #1
Switched to NOHz mode on CPU #0
...........................<6>Freeing initrd memory: 2k freed
fuse init (API version 7.11)
SGI XFS with security attributes, large block/inode numbers, no debug
enabled
msgmni has been set to 993
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
pci 0000:00:02.0: Boot video device
pci 0000:03:0f.0: Firmware left e100 interrupts enabled; disabling
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: setting latency timer to 64
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN0] (on)
ACPI: SSDT 1fab0270 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 1fab0500 0065D (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
Monitor-Mwait will be used to enter C-3 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
processor ACPI_CPU:00: registered as cooling_device1
ACPI: SSDT 1fab01a0 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 1fab0470 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
processor ACPI_CPU:01: registered as cooling_device2
ACPI Warning (nspredef-0949): \_TZ_.TZ01._PSL: Return Package type
mismatch at index 0 - found Processor, expected Reference [20090320]
ACPI: Expecting a [Reference] package element, found type C
ACPI: Invalid passive threshold
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ01] (23 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing
all legacy ISA IDE ports
ide-gd driver 1.18
ide-cd driver 5.00
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:01:00.0: setting latency timer to 64
0000:01:00.0: 0000:01:00.0: Failed to initialize MSI-X interrupts.
Falling back to MSI interrupts.
0000:01:00.0: 0000:01:00.0: Failed to initialize MSI interrupts.
Falling back to legacy interrupts.
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:12:cd:00:a5:58
0000:01:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:01:00.0: eth0: MAC: 3, PHY: 8, PBA No: ffffff-0ff
pcnet32.c:v1.35 21.Apr.2008 tsbogend@xxxxxxxxxxxxxxxx
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:03:0f.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e100 0000:03:0f.0: PME# disabled
e100: eth1: e100_probe: addr 0xcfdff000, irq 16, MAC addr 00:12:cd:00:a5:59
ThunderLAN driver v1.15a
TLAN: 0 devices installed, PCI: 0 EISA: 0
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-e (2.4 port) Sep-11-2006 Donald Becker
<becker@xxxxxxxxx>
http://www.scyld.com/network/drivers.html
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff5bc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000e080
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000ef00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please
boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
Freeing unused kernel memory: 328k freed
usb 1-3: new high speed USB device using ehci_hcd and address 3
usb 1-3: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: Microsoft Comfort Curve Keyboard 2000 as
/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input2
generic-usb 0003:045E:00DD.0001: input: USB HID v1.11 Keyboard
[Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-2/input0
input: Microsoft Comfort Curve Keyboard 2000 as
/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input3
generic-usb 0003:045E:00DD.0002: input: USB HID v1.11 Device [Microsoft
Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-2/input1
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as
/devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input4
generic-usb 0003:045E:0040.0003: input: USB HID v1.10 Mouse [Microsoft
Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.2-1/input0
usb 4-2: new full speed USB device using uhci_hcd and address 3
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda-intel: no codecs found!
HDA Intel 0000:00:1b.0: PCI INT A disabled
usb 4-2: configuration #1 chosen from 1 choice
Clocksource tsc unstable (delta = -274809009 ns)
scsi 0:0:0:0: Direct-Access 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 3948544 512-byte hardware sectors: (2.02 GB/1.88 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed
generic-usb 0003:0EEF:0001.0004: timeout initializing reports
input: eGalax Inc. USB TouchController as
/devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5
generic-usb 0003:0EEF:0001.0004: input,hiddev96: USB HID v2.10 Pointer
[eGalax Inc. USB TouchController] on usb-0000:00:1d.2-2/input0
---
SliTaz GNU/Linux Mailing list - http://www.slitaz.org/