[qet] Re: Loosing info by copy and paste

[laurent Trinques <scorpio@xxxxxxxxxxxxxxxx>]

Le jeudi 26 mars 2020, 10:44:14 CET MARCO NACCINI a écrit :
> Dear Laurent,
> 
>  there is a way to do a copy and paste of a list of connector pins without
> loose the label number and other information ?
> 
> Thank you
> 
> Marco
> 
> 
Dear Marco,

yes, don't check this checkbox, see attached capture.

Best regards,
Laurent 


> GORIZIANE GROUP S.P.A.
> Engineering & Construction
> Project Engineer
> Via Aquileia, 7
> ​34070 ​Villesse GO
> Italia
> +39 048191511
> +39 344 1732988
> marco.naccini@xxxxxxxxxxxx
> This message contains personal data according to Legislative Decree
> 196/2003, the consultation, processing, modification, store, diffusion and
> use of which in any procedure, way and extent on behalf of unauthorized
> subjects, according to not allowed manners or to purposes different from
> the agreed ones amounts to illegitimate treatment and source of grave
> penal, civil and administrative responsibility. In case of wrong receipt of
> this message, it is kindly asked to advise the sender immediately and to
> get rid of its contents -----Original Message-----
> From: laurent Trinques <scorpio@xxxxxxxxxxxxxxxx>
> Sent: martedì 17 marzo 2020 15:04
> To: qet@xxxxxxxxxxxxxxxxxxx
> Cc: MARCO NACCINI <marco.naccini@xxxxxxxxxxxx>
> Subject: Re: [qet] Replkace in XML
> 
> Le mardi 17 mars 2020, 13:08:16 CET MARCO NACCINI a écrit :
> > Hello I'm trying to use QElectroTech.
> > 
> > It is useful but I would like to ask some tricks.
> > 
> > I done a good drawing but I put some hundred of male pins but I
> > mistake a I would like to convert all of them to be female type.
> > 
> > I'm tryng to operate on xml file and I found that, apparently, the
> > only difference between male and female pins is this part:
> > 
> > embed://import/10_electric/10_allpole/140_connectors&amp;plugs/01_conn
> > ectors
> > _pins/connecteur_m.elmt">
> > 
> > instead then
> > 
> > embed://import/10_electric/10_allpole/140_connectors&amp;plugs/01_conn
> > ectors
> > _pins/connecteur_f.elmt">
> > 
> > Bus when I exchange one with the other I obtain that in QElectroTech
> > the pin disapper.
> > 
> > Do you have an idea how can I use xml to do it ?
> > 
> > In the attachment the file qet.
> > 
> > Can you help me ?
> > 
> > Thank you
> > 
> > 
> > Marco
> > 
> > GORIZIANE GROUP S.P.A.
> > Engineering & Construction
> > Project Engineer
> > Via Aquileia, 7
> > ​34070 ​Villesse GO
> > Italia
> > +39 048191511
> > +39 344 1732988
> > marco.naccini@xxxxxxxxxxxx
> > This message contains personal data according to Legislative Decree
> > 196/2003, the consultation, processing, modification, store, diffusion
> > and use of which in any procedure, way and extent on behalf of
> > unauthorized subjects, according to not allowed manners or to purposes
> > different from the agreed ones amounts to illegitimate treatment and
> > source of grave penal, civil and administrative responsibility. In
> > case of wrong receipt of this message, it is kindly asked to advise
> > the sender immediately and to get rid of its contents
> 
> Hello Marco,
> 
> see attached corrected dawning.
> In this case, just edit your male pins element put in your diagram make
> change, save element edited, save to another name (for backup)and launch
> this new project.
> 
> Best regards,
> Laurent

Attachment: label_paste.png
Description: PNG image