[crisos] usb pen/hd on darwinfox...

["Torben Dannhauer" <torben@xxxxxxxxxxxxxx>]

Hello,

 

i have the same problem:

 

How can I use a USB-Pen in Darwinfox?

 

If I connect a USB-Pen I get these messages in dmesg:

 

crisv10_irq dbg: ctr_status_irq, controller status: host_mode started

crisv10_irq dbg: ctr_status_irq, controller status: host_mode started running

usb 1-1: new full speed USB device using hc-crisv10 and address 2

usb 1-1: configuration #1 chosen from 1 choice

 

 

my devices which could be relevant  look like this:

 

crw-r--r--    1 root     root     189,   1 Jan  1 00:00 1-1

crw-r--r--    1 root     root      90,   0 Jan  1 00:00 mtd0

crw-r--r--    1 root     root      90,   1 Jan  1 00:00 mtd0ro

crw-r--r--    1 root     root      90,   2 Jan  1 00:00 mtd1

crw-r--r--    1 root     root      90,   3 Jan  1 00:00 mtd1ro

crw-r--r--    1 root     root      90,   4 Jan  1 00:00 mtd2

crw-r--r--    1 root     root      90,   5 Jan  1 00:00 mtd2ro

brw-r--r--    1 root     root      31,   0 Jan  1 00:00 mtdblock0

brw-r--r--    1 root     root      31,   1 Jan  1 00:00 mtdblock1

brw-r--r--    1 root     root      31,   2 Jan  1 00:00 mtdblock2

crw-r--r--    1 root     root     189,   0 Jan  1 00:00 usb1

crw-r--r--    1 root     root     254,   0 Jan  1 00:00 usbdev1.1_ep00

crw-r--r--    1 root     root     254,   1 Jan  1 00:00 usbdev1.1_ep81

crw-r--r--    1 root     root     254,   2 Jan  1 00:00 usbdev1.2_ep00

crw-r--r--    1 root     root     254,   4 Jan  1 00:00 usbdev1.2_ep02

crw-r--r--    1 root     root     254,   3 Jan  1 00:00 usbdev1.2_ep81

crw-rw-rw-    1 root     root       1,   5 Jan  1 00:00 zero

 

I supposed the USB-stick is the device “/dev/1-1”, because if c connect a second stick, I get the device “/dev/1-2”.

But if I try to mount or part it, I get errors:

 

mkfs.ext2 /dev/1-1

mke2fs 1.40.11 (17-June-2008)

/dev/1-1 is not a block special device.

Proceed anyway? (y,n) y

mkfs.ext2: Device size reported to be zero.  Invalid partition specified, or

        partition table wasn't reread after running fdisk, due to

        a modified partition being busy and in use.  You may need to reboot

        to re-read your partition table.

 

 

 

The same with “/dev/usb1” and “/dev/usbdev*”

 

The description an the acme-website (http://foxlx.acmesystems.it/?id=6) has the same beginning in dmesg, but is followed the the driver loading for scsi emulation… There is no Pakcage about scsi or anything like that in CrisOs/Darwinfox

 

 

How can I use a usbpen?

 

Thank you for your help

 

Torben Dannhauer